Description
BUY CD4060BE https://www.utsource.net/itm/p/248327.html
14-Stage Ripple-Carry Binary Counter/Divider And Oscillator14//
Below is the parameter table and instructions for the CD4060BE 14-stage binary ripple counter and oscillator.
CD4060BE Parameter Table
| Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
| Supply Voltage |
VDD |
3 |
- |
15 |
V |
| Output Low Voltage |
VOL |
0.2 |
- |
0.5 |
V (VDD = 5V) |
| Output High Voltage |
VOH |
2.4 |
- |
VDD - 1.5 |
V (VDD = 5V) |
| Input Low Voltage |
VIL |
0.8 |
- |
- |
V (VDD = 5V) |
| Input High Voltage |
VIH |
- |
- |
3.5 |
V (VDD = 5V) |
| Quiescent Current |
IQ |
- |
10 |
- |
μA (VDD = 5V) |
| Output Current (Sink) |
IOL |
- |
- |
10 |
mA (VDD = 5V) |
| Output Current (Source) |
IOH |
- |
- |
10 |
mA (VDD = 5V) |
| Operating Temperature Range |
TA |
-40 |
- |
85 |
°C |
| Storage Temperature Range |
TSTG |
-65 |
- |
150 |
°C |
CD4060BE Instructions
1. Pin Configuration
- 1 (Q14): 14th stage output
- 2 (Q13): 13th stage output
- 3 (Q12): 12th stage output
- 4 (Q11): 11th stage output
- 5 (Q10): 10th stage output
- 6 (Q9): 9th stage output
- 7 (Q8): 8th stage output
- 8 (GND): Ground
- 9 (Q7): 7th stage output
- 10 (Q6): 6th stage output
- 11 (Q5): 5th stage output
- 12 (Q4): 4th stage output
- 13 (Q3): 3rd stage output
- 14 (Q2): 2nd stage output
- 15 (Q1): 1st stage output
- 16 (VDD): Power supply
- 9 (R1): Oscillator resistor input
- 10 (R2): Oscillator resistor input
- 11 (C1): Oscillator capacitor input
2. Oscillator Circuit
The CD4060BE can be used as a simple oscillator by connecting an external resistor (R1) and capacitor (C1) between the oscillator pins (9, 10, and 11).
- R1 and R2 are connected to the oscillator input.
- C1 is connected between the oscillator input and ground.
3. Frequency Calculation
The frequency of the oscillator can be calculated using the following formula:
[ f = frac{2.3 times R times C} ]
Where:
- ( f ) is the frequency in Hz.
- ( R ) is the resistance in ohms.
- ( C ) is the capacitance in farads.
4. Output Stages
The CD4060BE has 14 output stages (Q1 to Q14). Each stage divides the input frequency by 2, providing a binary count sequence.
5. Powering the IC
- Connect the power supply (VDD) to pin 16.
- Connect the ground (GND) to pin 8.
6. Using the Outputs
- The outputs (Q1 to Q14) can be used to drive other logic circuits or LEDs.
- Ensure that the load on each output does not exceed the maximum output current ratings.
7. Reset Function
- The reset function is not available on the CD4060BE. To reset the counter, you can use an external reset circuit or simply power cycle the IC.
8. Operating Conditions
- Ensure that the operating temperature and supply voltage are within the specified ranges to avoid damage to the IC.
9. Storage Conditions
- Store the IC in a dry environment to prevent moisture damage.
By following these instructions, you can effectively use the CD4060BE in your digital circuits.
(For reference only)
More detail about Utsource Holding Company Limited
