Product Description
The Festo VTSA-F-FB-AP is a flow-optimised valve terminal that integrates the high-performance VTSA-F pneumatic platform with the advanced CPX-AP-A automation system, featuring an AP fieldbus interface for real-time Ethernet-based communication . This Type 45 terminal supports five different valve sizes (18 mm to 65 mm) on one manifold, delivering flow rates from 700 l/min up to 4,000 l/min, with a maximum of 32 valve positions and 16 independent pressure zones .
Key Features & Advantages
CPX-AP-A Automation System Integration: The terminal connects a CPX-AP-A automation system to the VTSA-F-FB valve terminal via the VABA-S6-1-X5-F4 pneumatic interface . All AP-based modules share a single IP address, simplifying commissioning and enabling smaller, more cost-effective PLCs
Flow-Optimised Design with Higher Flow Rates: Delivers increased flow rates – 700 l/min (18 mm), 1,350 l/min (26 mm), 1,860 l/min (42 mm), 2,900 l/min (52 mm), and 4,000 l/min (65 mm)
Five Mixable Valve Sizes: Supports 18 mm, 26 mm, 42 mm, 52 mm, and 65 mm valve sizes on one terminal, allowing optimised flow capacity selection per valve position without adapters
High Valve Position Capacity: Accommodates up to 32 valve positions and up to 16 independent pressure zones
AP Fieldbus Protocol: Features AP (Automation Protocol) with Ethernet-based communication, 100 Mbit/s transmission rate, internal cycle time <1 ms, and support for EDS, ESI, GSDML, and IODD configuration files
IP65 Protection Class: Dust-tight and protected against water jets, suitable for washdown environments and demanding industrial conditions
No Corrosion Stress Construction: Rated CRC 0 – No corrosion stress, ensuring exceptional durability for harsh industrial environments
ATEX Zone 2 Certification: Certified for potentially explosive gas atmospheres, suitable for chemical, petrochemical, and pharmaceutical facilities
LABS (PWIS) Conformity: Complies with VDMA24364-B1/B2-L standards for paint-wetting impairment substances
Extensive Valve Function Range: Available in 5/2 monostable/bistable, 5/3 pressurised/exhausted/closed, 2x3/2, 2x2/2, and safety function variants
Vacuum Capable: Suitable for vacuum applications down to -0.9 bar
Low Power Consumption: 5/2 and 5/3 valves consume 1.6 W (72 mA) per coil at 24 V DC
Internal or External Pilot Air Supply: Supports both configurations (3 bar to 10 bar pilot pressure)
LED Status Indication: Clear LED indicators for valve status, module diagnostics (MD), and load power supply (PL)
Modular Design with Mixed Valve Sizes: Type 45 terminal with modular construction allows mixing different valve sizes on a single manifold
Colour-Coded Pneumatic Interface: The VABA-S6-1-X5-F4 interface has colour-coded connectors to prevent mixing with VTSA-F-CB serial communication modules
Wide Ambient Temperature Range: Operates reliably from -5°C to +50°C
c UL us & RCM Certified: Carries c UL us - Recognized (OL) and RCM compliance mark certifications
CE Marked for EMC & RoHS: Meets EU EMC Directive and EU RoHS Directive requirements
RoHS Compliant, Halogen-Free, Phosphate-Free: Manufactured without restricted hazardous substances
Technical Specifications
Brand: Festo
Model: VTSA-F-FB-AP
Product No.: 8130719
Product Type: Valve Terminal / Pneumatic Valve Manifold with CPX-AP-A Automation System
Terminal Type: 45
Valve Sizes Supported: 18 mm, 26 mm, 42 mm, 52 mm, 65 mm
Max. Number of Valve Positions: 32
Max. Number of Pressure Zones: 16
Max. Number of CPX-AP-A Modules: 15
Standard Nominal Flow Rate: 700 l/min (18 mm), 1,350 l/min (26 mm), 1,860 l/min (42 mm), 2,900 l/min (52 mm), 4,000 l/min (65 mm)
Operating Pressure: -0.9 bar to 10 bar (internal pilot: 3 bar to 10 bar)
Vacuum Suitability: Yes
Operating Medium: Compressed air to ISO 8573-1:2010 [7:4:4]
Media Note: Lubricated operation possible (in which case lubricated operation will always be required thereafter)
Corrosion Resistance Class (CRC): 0 – No corrosion stress
LABS (PWIS) Conformity: VDMA24364-B1/B2-L
Degree of Protection: IP65
Ambient Temperature: -5°C to +50°C
Storage Temperature: -20°C to +60°C
Maximum Installation Height: 3,500 m
Pollution Degree: 2
CE Marking: EU EMC Directive, EU RoHS Directive
c UL us Certification: Recognized (OL) – UL E322346
RCM Mark: Yes
Pilot Pressure: 3 bar to 10 bar
Pilot Air Supply: Internal or External
Nominal Operating Voltage DC Electronics/Sensors: 24 V (±25%)
Nominal Operating Voltage DC Load (Valves): 24 V (±10%)
Power Supply Requirements: SELV/PELV according to IEC 60204-1
Galvanic Isolation: Yes, between electronics/sensors and load/valves
Reverse Polarity Protection: Yes
Power Failure Bridging: 10 ms
Electrical Communication: AP fieldbus interface (Ethernet-based)
Fieldbus Transmission Rate: 100 Mbit/s
Internal Cycle Time: <1 ms
Maximum Address Capacity Input: 4,096 Byte
Maximum Address Capacity Output: 4,096 Byte
Configuration Support: EDS file, ESI file, GSDML file, IODD file
Signal Status Display: LED (valve status, module diagnostics MD, load power PL)
Valve Functions Available: 5/2 monostable, 5/2 bistable, 5/2 bistable with dominant signal, 5/2 monostable with safety function, 5/3 pressurised, 5/3 exhausted, 5/3 closed, 2x3/2 normally closed monostable, 2x3/2 normally open monostable, 2x3/2 open/closed monostable, 2x2/2 normally closed monostable
Valve Design: Piston spool (piston gate valve)
Sealing Principle: Soft
Exhaust Air Function: Via throttle plate
Pneumatic Working Port Options: G1/8, G1/4, G3/8, G1/2, QS-6, QS-8, QS-10, QS-12, QS-14, QS-16
Type of Mounting: H-rail (EN 60715), mounting frame, screw clamping, through-hole for M5/M6 screws
Tightening Torque – Earthing Screw: 1.0 Nm ±10%
Tightening Torque – Tie Rods: 2.0 Nm ±15%
Tightening Torque – M12 Connector: 0.5 Nm
Tightening Torque – M8 Connector: 0.25 Nm to 0.5 Nm
Seals Material: NBR
Housing Material: Powder-coated die-cast zinc and aluminium alloys
Material Note: RoHS-compliant, Halogen-free, Phosphate-free, LABS (PWIS) conformity
Country of Origin: Germany
Compatible CPX-AP-A Bus Interfaces (from Festo documentation)
CPX-AP-A-PN-CU (8129245) – PROFINET interface, copper connection
CPX-AP-A-PN-M12 (8129241) – PROFINET interface, M12 connection
Remote I/O system CPX-AP-A (8079933)
Pneumatic Interface (from Festo documentation)
VABA-S6-1-X5-F4 – Pneumatic interface connecting CPX-AP-A automation system with VTSA-F-FB valve terminal
Colour-coded connectors prevent mixing with VTSA-F-CB serial communication modules (parallel connection for FB/F-FB)
Features LED MD (module diagnostics) and LED PL (load power supply)
Connections: XD1 push-pull system power supply, XD2 push-pull voltage forwarding
Ideal For
Large-scale industrial automation systems requiring CPX-AP-A remote I/O architecture with AP fieldbus communication, automotive manufacturing (welding lines, assembly), machine tools, packaging machinery, material handling systems, paint shop environments requiring LABS conformity, potentially explosive atmospheres ATEX Zone 2, vacuum applications down to -0.9 bar, systems requiring IP65 washdown protection, and integration with CPX-AP-A fieldbus systems for real-time Ethernet-based control.
Why Choose Festo VTSA-F-FB-AP Valve Terminal?
Choose the Festo VTSA-F-FB-AP for its flow-optimised design delivering higher flow rates (700-4,000 l/min) than standard VTSA, CPX-AP-A automation system integration with AP fieldbus interface (100 Mbit/s, <1 ms cycle time) for real-time Ethernet communication, supporting up to 32 valve positions and 16 pressure zones, featuring five mixable valve sizes (18-65 mm) on a Type 45 terminal, CRC 0 corrosion resistance, IP65 protection, LABS conformity (VDMA24364-B1/B2-L), vacuum capability down to -0.9 bar, low power consumption (1.6 W/1.3 W), extensive valve function options, internal or external pilot air supply (3-10 bar), LED status indication (MD, PL), colour-coded pneumatic interface to prevent module mixing, c UL us, RCM, and CE certifications, RoHS compliance with halogen-free and phosphate-free materials, full configuration file support (GSDML for PROFINET, ESI for EtherNet/IP, IODD for IO-Link), and German engineering quality. Backed by Festo's comprehensive CPX-AP-A system ecosystem including PROFINET bus nodes, I/O modules, and the VABA-S6-1-X5-F4 pneumatic interface with push-pull connections, this flow-optimised valve terminal delivers reliable, flexible, and safe pneumatic control for demanding industrial automation applications with advanced fieldbus connectivity.
Tags
#Festo #VTSAFFBAP #8130719 #ValveTerminal #ValveManifold #CPXAPA #APFieldbus #VTSAF #Type45 #IP65 #CRC0 #LABSConformant #PROFINET #HighFlow #PneumaticControl #ModularValveTerminal #cULus #RCM #MalaysiaSupplier
Tingnan ang karagdagang mga detalye tungkol sa GREX IND SUPPLY
Malaysia
