| input |
| type of the power supply network |
1-phase AC or DC |
| supply voltage at AC |
|
| ● minimum rated value |
100 V |
| ● maximum rated value |
240 V |
| ● initial value |
85 V |
| ● full-scale value |
264 V |
| input voltage at DC |
110 ... 300 V |
| wide range input |
Yes |
| overvoltage overload capability |
300 V AC for 1 s |
| buffering time for rated value of the output current in the event of power failure minimum |
40 ms |
| operating condition of the mains buffering |
at Vin = 187 V |
| line frequency |
50/60 Hz |
| line frequency |
47 ... 63 Hz |
| input current |
|
| ● at rated input voltage 120 V |
0.3 A |
| ● at rated input voltage 230 V |
0.2 A |
| current limitation of inrush current at 25 °C maximum |
20 A |
| I2t value maximum |
0.8 A²·s |
| fuse protection type |
internal |
| fuse protection type in the feeder |
Recommended miniature circuit breaker: from 6 A characteristic B or from 2 A characteristic C |
| output |
| voltage curve at output |
Controlled, isolated DC voltage |
| output voltage at DC rated value |
24 V |
| output voltage |
|
| ● at output 1 at DC rated value |
24 V |
| |
|
| output voltage adjustable |
No |
| relative overall tolerance of the voltage |
3 % |
| relative control precision of the output voltage |
|
| ● on slow fluctuation of input voltage |
0.1 % |
| ● on slow fluctuation of ohm loading |
0.1 % |
| residual ripple |
|
| ● maximum |
200 mV |
| ● typical |
30 mV |
| voltage peak |
|
| ● maximum |
300 mV |
| ● typical |
50 mV |
| display version for normal operation |
Green LED for output voltage OK |
| behavior of the output voltage when switching on |
No overshoot of Vout (soft start) |
| response delay maximum |
0.5 s |
| voltage increase time of the output voltage |
|
| ● typical |
100 ms |
| output current |
|
| ● rated value |
0.6 A |
| ● rated range |
0 ... 0.6 A; +55 ... +70 °C: Derating 2%/K |
| |
|
| supplied active power typical |
14.4 W |
| bridging of equipment |
No |
| efficiency |
| efficiency in percent |
81 % |
| power loss [W] |
|
| ● at rated output voltage for rated value of the output current typical |
3.4 W |
| ● during no-load operation maximum |
0.3 W |
| closed-loop control |
| relative control precision of the output voltage with rapid fluctuation of the input voltage by +/- 15% typical |
0.2 % |
| relative control precision of the output voltage at load step of resistive load 10/90/10 % typical |
2 % |
| setting time |
|
| ● load step 10 to 90% typical |
1 ms |
| ● load step 90 to 10% typical |
1 ms |
| protection and monitoring |
| design of the overvoltage protection |
Yes, according to EN 60950-1 |
| property of the output short-circuit proof |
Yes |
| design of short-circuit protection |
Constant current characteristic |
| ● typical |
0.8 A |
| overcurrent overload capability |
|
| ● when switching on |
150% Iout rated typ. 200 ms |
| ● in normal operation |
overload capability 150% Iout rated typ. 200 ms |
| enduring short circuit current RMS value |
|
| ● maximum |
0.8 A |
| measuring point for output current |
No |
| safety |
| galvanic isolation between input and output |
Yes |
| galvanic isolation |
Safety extra-low output voltage Uout acc. to EN 60950-1 and EN 50178 |
| operating resource protection class |
Class II (without protective conductor) |
| protection class IP |
IP20 |
| EMC |
| standard |
|
| ● for emitted interference |
EN 55022 Class B |
| ● for mains harmonics limitation |
not applicable |
| ● for interference immunity |
EN 61000-6-2 |
| standards, specifications, approvals |
| certificate of suitability |
|
| ● CE marking |
Yes |
| ● UL approval |
Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus-Recognized (UL 60950, CSA C22.2 No. 60950), File E151273, NEC class 2 (acc. to UL 1310) |
| ● CSA approval |
Yes; cULus-Listed (UL 508, CSA C22.2 No. 107.1), File E197259; cURus-Recognized (UL 60950, CSA C22.2 No. 60950), File E151273, NEC class 2 (acc. to UL 1310) |
| ● EAC approval |
Yes |
| ● NEC Class 2 |
Yes; according to UL1310, File E151273 |
| ● SEMI F47 |
Yes |
| type of certification |
|
| ● CB-certificate |
Yes |
| MTBF at 40 °C |
4 415 040 h |
| standards, specifications, approvals hazardous environments |
| certificate of suitability |
|
| ● IECEx |
No |
| ● ATEX |
No |
| ● ULhazloc approval |
No |
| ● cCSAus, Class 1, Division 2 |
No |
| ● FM registration |
No |
| standards, specifications, approvals marine classification |
| shipbuilding approval |
Yes |
| Marine classification association |
|
| ● American Bureau of Shipping Europe Ltd. (ABS) |
Yes |
| ● French marine classification society (BV) |
Yes |
| ● Det Norske Veritas (DNV) |
Yes |
| ● Lloyds Register of Shipping (LRS) |
Yes |
| standards, specifications, approvals Environmental Product Declaration |
| Environmental Product Declaration |
Yes |
| global warming potential [CO2 eq] |
|
| ● total |
94.5 kg |
| ● during manufacturing |
1.3 kg |
| ● during operation |
93.1 kg |
| ● after end of life |
0.05 kg |
| ambient conditions |
| ambient temperature |
|
| ● during operation |
-25 ... +70 °C; with natural convection |
| ● during transport |
-40 ... +85 °C |
| ● during storage |
-40 ... +85 °C |
| environmental category according to IEC 60721 |
Climate class 3K3, 5 ... 95% no condensation |
| connection method |
| type of electrical connection |
screw terminal |
| ● at input |
L, N: 1 screw terminal each for 0.5 ... 2.5 mm2 single-core/finely stranded |
| ● at output |
+, -: 1 screw terminal each for 0.5 ... 2.5 mm² |
| ● for auxiliary contacts |
- |
| mechanical data |
| width × height × depth of the enclosure |
18 × 90 × 53 mm |
| installation width × mounting height |
18 mm × 130 mm |
| required spacing |
|
| ● top |
20 mm |
| ● bottom |
20 mm |
| ● left |
0 mm |
| ● right |
0 mm |
| fastening method |
Snaps onto DIN rail EN 60715 35x7.5/15, direct mounting in different mounting positions |
| ● DIN-rail mounting |
Yes |
| ● S7 rail mounting |
No |
| ● wall mounting |
Yes |
| housing can be lined up |
Yes |
| net weight |
0.07 kg |
Malaysia
