Description
CA-20D Online Thermal Camera Analyzer
Overview
CA-20 entry-level thermal analyzer can analyze thermal failures, heat conduction and heat distribution of circuit boards and materials. The CA-20D equipped with 260*200 detector resolution, which not only detect temperature changes of electronic components and heating & heat sink materials, the relatively rich software functions can also record a variety of test data.
In addition to meeting all the diagnostic functions of the CA-09D for circuit board repairing, the CA-20 can also perform thermal analysis data recording and analysis. It is a very cost-effective, entry-level thermal analysis instrument
Analysis mode
Circuit board analysis mode
Analysis mode of E-cigarette atomizer
Multi-dimensional analysis mode
Analysis mode of material thermal capacity
Defect analysis mode
Application Scenario
Analysis of the thermal design of the circuit board
When the circuit board chip heats up, users can check the components affected by the heat to adjust the layout.
Detection and analysis of heat conduction material
When the heat conduction material conducts heat, different color blocks can be set to view the distribution of heat conduction.
Temperature control analysis of E-cigarette
Quickly tracking the heating rate and temperature of the atomizer
Thermal quality analysis of products and components
The aging degree of the tested components can be analyzed through the simultaneous comparison of the standard samples and the tested samples.
Circuit board pulse heating analysis
The thermal analyzer can quickly capture the occasional pulse heat emitted by some components on the circuit board due to failure.
Material heat dissipation analysis
The heat dissipation of different heat dissipation materials can be analyzed through the temperature color block.
Analysis of the corresponding relationship between voltage, current and temperature
Heating capacity analysis of heating materials at different voltages and currents
The heating rate, heating efficiency and heating temperature of materials such as heating wire and heating sheet at different voltages and currents can be quantitatively analyzed.
Location detection of short circuit and leakage
When repairing the circuit board, the leakage position can be located through the first, second and third high temperature points.
Specification
| System parameters |
CA-20
|
CA-30
|
CA-60
|
| IR resolution |
260*200
|
384*288
|
640*512
|
| Spectral range |
8~14um
|
| NETD |
70mK@25℃
|
50mK@25℃
|
| FOV |
42°x32°
|
41.1°x30.8°
|
45.7°x37.3°
|
| Frame rate |
25Hz
|
| Focus mode |
Manual focus
|
| Working temperature |
-10℃~+55℃
|
| Measurement and analysis |
| Temperature range |
-10℃~450℃
|
-10℃~550℃
|
-10℃~550℃
|
| Temperature measurement method |
Maximum temperature, minimum temperature and average temperature
|
| Temperature measurement accuracy |
±2 or ±2% for -10℃~120℃, and ±3% for 120℃~550℃
|
| Measuring distance |
3~150 cm
|
4~200 cm
|
4~200 cm |
| Temperature correction |
Manual/Automatic
|
| Emissivity correction |
Adjustable within 0.1-1.0
|
| Data sampling frequency |
It can be configured flexibly, such as 20FPS, 10FPS, 5FPS, 1FPS.
|
| Image file |
Full-temperature JPG thermogram (Radiometric-JPG)
|
| Video file |
MP4
|
| Device dimension |
| Single board |
220mm x 172mm, height of 241mm
|
| Double board |
346mm x 220mm, height of 341mm
|
| Data acquisition accessories (not included in standard configuration) |
| Heating table |
Standard configuration of 2 oiling test holes of resistance heating wires, which can be customized
|
| |
Customized adjustment of the simulated suction degree, duration and times of the suction pump
|
| Data acquisition |
Recording of temperature data without time limit, including temperature change data, data corresponding to resistance heating wires and resistance values, data corresponding to simulated power supply time and temperature, and calculation of heating uniformity
|
More detail about MTM Precision Sdn Bhd
Malaysia
